Your teacher writes your IA2. This is the QCAA sample, so use it for the question shapes, and ask your teacher for practice that matches your school’s paper.
A polymer with a yield strength of 55 MPa is used in an application which requires a factor of safety of 3.2. What is the maximum allowable working stress for this polymer?
Not quite. The digits 58 come from the division done upside down, $3.2 \div 55 = 0.058$, with the decimal point then moved one place. Divide the yield strength by the factor of safety.
Not quite. You have the right digits and the wrong decimal place. $55 \div 3.2$ is ten times this. The allowable stress is smaller than the yield strength, but not thirty times smaller.
Not quite. The digits 58 come from the division done upside down, $3.2 \div 55 = 0.058$, then read as 5.8. Divide the yield strength by the factor of safety.
That is it. Step through the hints below to see why.
Grey bar: the yield strength, 55 MPa. Solid orange bar: the working stress in the option you are testing. Pale orange bar with dividers: 3.2 lots of that working stress laid end to end. With the right working stress the pale bar ends on the dashed blue line at 55 MPa.
Nothing is being tested yet. Choose Test (A), (B), (C) or (D) above.
A working stress of 0.58 MPa would give a factor of safety of $55 \div 0.58 = 94.8$, not 3.2. Lay 3.2 lots of it end to end and you reach only 1.86 MPa. The digits 58 come from the division done upside down, $3.2 \div 55 = 0.058$, with the decimal point then moved one place.
A working stress of 1.72 MPa would give a factor of safety of $55 \div 1.72 = 32.0$, ten times the 3.2 asked for. 3.2 lots of it reach only 5.50 MPa. These are the right digits with the decimal point one place out.
A working stress of 5.8 MPa would give a factor of safety of $55 \div 5.8 = 9.48$, not 3.2. 3.2 lots of it reach only 18.6 MPa. The digits 58 come from the division done upside down, $3.2 \div 55 = 0.058$, then read as 5.8.
A working stress of 17.2 MPa gives a factor of safety of $55 \div 17.2 = 3.20$. 3.2 lots of it reach 55.0 MPa, which is the yield strength.
Try the question first. Choose a hint above when you want one.
The formula book gives the factor of safety as the yield stress divided by the allowable working stress. You want the allowable working stress, so rearrange it.
$$\begin{aligned}&\text{allowable working stress}\\&=\frac{\text{yield stress}}{\text{factor of safety}}\end{aligned}$$
A factor of safety of 3.2 means the material could carry 3.2 times the working stress before it yields.
$$\begin{aligned}&\text{allowable working stress}\\&=\frac{55}{3.2}=17.2\ \text{MPa}\end{aligned}$$
This is option (D).
The allowable stress must be smaller than the yield strength, and with a factor of about 3 it is about a third of it. An answer near 1 MPa or 6 MPa is far too small.
$\text{allowable working stress}=\dfrac{\text{yield stress}}{\text{factor of safety}}=\dfrac{55}{3.2}=17.2$ MPa.
Only mark this done when you could do it without help. Reading the solution does not count.
Question wording is from the QCAA Engineering 2025 v1.4 IA2 sample assessment instrument, and the marker lines are from its sample marking scheme, © State of Queensland (QCAA) 2026, licensed under CC BY 4.0. Figures are redrawn. The solutions, animations and commentary are Tangent Tuition’s. Tangent Tuition is not affiliated with the QCAA.
Spot a mistake on this page? Report it