Engineering · Unit 3 · QCAA sample IA2 All sample IA2 questions
QCAA sample IA2 · Section 1 · Multiple choice

Question 8

[1 mark]

Your teacher writes your IA2. This is the QCAA sample, so use it for the question shapes, and ask your teacher for practice that matches your school’s paper.

The question [1 mark]

A cylindrical steel test specimen with a diameter of 10 mm is subjected to a tensile test. The maximum force recorded before fracture is 78 kN. What is the ultimate tensile strength of the material?

Not quite. Your answer matches no single slip that I can find, so check its size. A material with a strength of 100 MPa would break at $100 \times 78.54 = 7854$ N, about a tenth of the 78 kN recorded.

Not quite. No tidy slip gives exactly 500 MPa. If you doubled the area you would get 497 MPa, which is close but is not 500. A material with a strength of 500 MPa would break at about 39.3 kN, half of the force recorded.

That is it. Step through the hints below to see why.

Not quite. 785 has the digits of the area, $\pi \times 5^2 = 78.5$ mm², not of the stress. You still need to divide the force by that area.

Cross-section 10 mm A = π × 5² = 78.54 mm² 78 kN recorded 0 05001000 MPa

Top left: the specimen, with blue arrows pointing outwards for the tension. Below it: the cross-section. Black bars: the force on the specimen and the stress it causes. Dashed orange lines: the UTS in the option you are testing, and the force at which a specimen with that UTS breaks. The force bar stops at the 78 kN the machine recorded.

Nothing is being tested yet. Choose Test (A), (B), (C) or (D) above.

With a UTS of 100 MPa this specimen would break at $100 \times 78.54 = 7854$ N, about 7.85 kN. The machine recorded 78 kN, ten times as much. I cannot find a single slip that turns these numbers into 100 MPa, so this option fails on size alone.

With a UTS of 500 MPa this specimen would break at $500 \times 78.54 = 39\,270$ N, about 39.3 kN, half of the 78 kN recorded. No tidy slip gives exactly 500. Doubling the area gives 497 MPa, which is close but is not 500.

With a UTS of 993 MPa this specimen breaks at $993 \times 78.54 = 77\,990$ N, which is 78.0 kN. That is the maximum force the machine recorded.

With a UTS of 785 MPa this specimen would break at $785 \times 78.54 = 61\,654$ N, about 61.7 kN, well short of the 78 kN recorded. 785 has the digits of the area, 78.5 mm², not of the stress.

Try the question first. Choose a hint above when you want one.

Stress needs the cross-sectional area. The specimen is a cylinder, so the cross-section is a circle. The diameter is 10 mm, so the radius is 5 mm.

$$A=\pi r^2=\pi\times5^2=78.54\ \text{mm}^2$$

Change the force to newtons: 78 kN is 78 000 N.

Why?

Newtons divided by square millimetres gives megapascals, the unit of every option.

The ultimate tensile strength is the maximum force divided by the original cross-sectional area.

$$\text{UTS}=\frac{78\,000}{\pi\times5^2}=993\ \text{MPa}$$

This is option (C).

Why?

A 10 mm bar has an area of about 78.5 mm², so every 78.5 N on it is 1 MPa. A force of 78 kN is therefore close to 1000 MPa, which rules out the other options before you calculate.

The radius is 5 mm and 78 kN is 78 000 N, so $\text{UTS}=\dfrac{78\,000}{\pi\times5^2}=993$ MPa.

(C)

Only mark this done when you could do it without help. Reading the solution does not count.

Back to the index

Question wording is from the QCAA Engineering 2025 v1.4 IA2 sample assessment instrument, and the marker lines are from its sample marking scheme, © State of Queensland (QCAA) 2026, licensed under CC BY 4.0. Figures are redrawn. The solutions, animations and commentary are Tangent Tuition’s. Tangent Tuition is not affiliated with the QCAA.