Engineering · Unit 3 · QCAA sample IA2 All sample IA2 questions
QCAA sample IA2 · Section 1 · Multiple choice

Question 6

[1 mark]

Your teacher writes your IA2. This is the QCAA sample, so use it for the question shapes, and ask your teacher for practice that matches your school’s paper.

The question [1 mark]

A concrete sample is known to have a compressive Young’s modulus of 25 GPa. What is the strain experienced by a sample when it is under 875 MPa of stress?

Not quite. You divided the wrong way up and left the units alone: $25 \div 875 = 0.0286$, which reads as 2.9%. Strain is the stress divided by the modulus.

That is it. Step through the hints below to see why.

Not quite. No clean slip gives exactly 28. The nearest is the modulus divided by the stress, $25\,000 \div 875 = 28.6$, which is upside down. Strain is the stress divided by the modulus.

Not quite. You worked out $875 \div 25 = 35$ without changing 25 GPa to 25 000 MPa, then read the 35 as a percentage.

concrete drawn 200 mm Question: E = 25 GPa 010 00020 00030 000 Young’s modulus (MPa)

The question gives no height for the sample. I have drawn it 200 mm tall for illustration only, so that each 1% of strain shows as 2 mm. Dashed outline: the sample before loading. Orange arrows pointing in: the compressive stress. Black bar: the modulus in the question. Orange bar: the modulus the option you are testing would need. Dashed blue line: 25 000 MPa.

Nothing is being tested yet. Choose Test (A), (B), (C) or (D) above.

A strain of 2.9% would need a modulus of $875 \div 0.029 = 30\,172$ MPa, about 30.2 GPa, not 25 GPa. You get this option by dividing the wrong way up with the units left alone: $25 \div 875 = 0.0286$, read as 2.9%.

A strain of 3.5% needs a modulus of $875 \div 0.035 = 25\,000$ MPa, which is the 25 GPa in the question. The two bars line up. Drawn 200 mm tall, the sample ends up 7.0 mm shorter.

A strain of 28% would need a modulus of only $875 \div 0.28 = 3125$ MPa, about 3.1 GPa. The nearest working is the division done upside down, $25\,000 \div 875 = 28.6$, but that rounds to 29, so no clean slip lands exactly on 28.

A strain of 35% would need a modulus of $875 \div 0.35 = 2500$ MPa, which is 2.5 GPa, a tenth of the modulus given. You get this option from $875 \div 25 = 35$: the gigapascals were never changed to megapascals, and the 35 was read as a percentage.

Try the question first. Choose a hint above when you want one.

The modulus is in gigapascals and the stress is in megapascals. Put both in the same unit before you divide.

$$25\ \text{GPa}=25\,000\ \text{MPa}$$

Why?

One gigapascal is 1000 megapascals. Strain has no unit, so the units of stress and modulus must cancel.

Young’s modulus is stress divided by strain, so strain is stress divided by Young’s modulus.

$$\varepsilon=\frac{\sigma}{E}=\frac{875}{25\,000}=0.035$$

Why?

Rearranging $E=\dfrac{\sigma}{\varepsilon}$ puts the stress on top. A stiffer material strains less under the same stress.

The options are percentages, so multiply the decimal by 100.

$$0.035\times100\%=3.5\%$$

This is option (B).

Put both in the same unit first: 25 GPa is 25 000 MPa. Then $\varepsilon=\dfrac{\sigma}{E}=\dfrac{875}{25\,000}=0.035=3.5\%$.

The numbers in this question are for arithmetic only. Real concrete crushes at a few tens of megapascals, far below 875 MPa.

(B)

Only mark this done when you could do it without help. Reading the solution does not count.

Back to the index

Question wording is from the QCAA Engineering 2025 v1.4 IA2 sample assessment instrument, and the marker lines are from its sample marking scheme, © State of Queensland (QCAA) 2026, licensed under CC BY 4.0. Figures are redrawn. The solutions, animations and commentary are Tangent Tuition’s. Tangent Tuition is not affiliated with the QCAA.