Topic guide 5 · Unit 3 Topic 2 · Civil structures and forces

Trusses: reactions and the method of joints

A truss is a frame of straight members joined into triangles. Bridges, roof frames, transmission towers and crane booms are trusses. They span a long way with little material, because each member is only ever pulled or pushed along its length.

Trusses are the largest topic in the QCAA sample IA2. This guide covers the reactions and the method of joints, where you balance the forces at one joint at a time. The next guide covers the method of sections. Tick off each skill once you can do it without help.

19
marks on trusses in the 78-mark QCAA sample IA2, the most of any topic
4 of 4
sample truss questions that ask for a force diagram
2
marks for each member asked for in Questions 19 and 21: one for the size of the force, one for tension or compression

Your teacher writes your IA2

Your IA2 is written by your teacher, not the QCAA. These guides are built to the syllabus and the QCAA sample exam, so the question shapes will be familiar. For practice that matches your school’s paper, your teacher is the best source.

Skills in this topic

Only tick a skill when you could do it in the exam. Your ticks are saved in this browser only.

Part 1

What the IA2 asks about trusses

The QCAA sample IA2 has four truss questions, all in Section 2, worth 19 of its 78 marks. Three of them are covered here.

QuestionMarksWhat it asks
183The two reactions of a triangular truss with one load on top.
195The forces in two members that meet at a support, given the reaction.
215The force in one member at a roller joint where three members meet, given the reaction and one member force.
256The force in one member in the middle of a truss. This is the method of sections, in the next guide.

What the syllabus says

  • •Interpret and perform calculations on simple truss frame forms, including actions (loads), reactions at supports with horizontal, vertical and angled loading considered, and method of joints and method of sections (graphical and analytical methods).

“Analytical” means by calculation. “Graphical” means by scale drawing. Both are named, which is one reason a protractor and a ruler are on the equipment list for the IA2.

How the sample marks a member force

Every truss question in the sample says “Include a force diagram”, and the diagram earns a mark each time, on its own in Questions 18, 19 and 21. In Questions 19 and 21 each member then earns two separate marks: one for the size of the force and one for saying whether it is tension or compression. In Question 19 that is $1 + 2 + 2 = 5$ marks.

A number with no “tension” or “compression” after it gets half the marks for that member.

What the formula book gives you

The Statics section has $F_H = F\cos\theta$, $F_V = F\sin\theta$, $M = Fd$ and the trigonometric ratios. It does not print the equilibrium conditions $\Sigma F_H = 0$, $\Sigma F_V = 0$ and $\Sigma M = 0$, and it has nothing specific to trusses.

Part 2

Tension and compression

Truss analysis rests on three assumptions. The members are joined by pins that cannot pass on any turning effect. The loads and reactions act only at the joints. The members have no weight worth counting. Under those assumptions each member has a force at each end and nothing in between, so the force must run straight along the member.

That leaves two possibilities for every member. It is being stretched, which is tension, or it is being squashed, which is compression.

A member in tension pulls on the joints at its ends. A member in compression pushes on them. In these guides tension is blue and compression is orange.

The arrows that matter are the ones on the joint. You will be drawing a force diagram of a joint, so you draw what the member does to that joint.

The member is inWhat it does to the jointArrow on the joint
TensionPulls the joint towards the memberPoints away from the joint
CompressionPushes the joint away from the memberPoints towards the joint

Students often draw these backwards because they picture what happens to the member. Picture a rope and a prop instead. A rope can only pull on what it is tied to. A prop can only push.

Why it matters which one it is

A member in tension can be thin, like a steel rod or a cable, and it fails by snapping. A slender member in compression fails by buckling sideways long before the material is crushed, so it has to be stockier. An engineer cannot size a member without knowing which it is, and that is why the nature of the force earns its own mark.

Not to scale. The sideways bow of the compression member is exaggerated.

Part 3

Reactions of a truss

To find the reactions, ignore the inside of the truss. The whole truss is one rigid body sitting on a pin and a roller, so it is solved exactly like a beam. Take moments about one support, then sum the forces. Guide 4 has the full method.

The only new step is finding distances. The moment of a vertical load depends on its horizontal distance from the support, and a question may give you member lengths instead. Use the geometry to get the horizontal distances first.

Practise

Sample IA2 question: reactions of a truss

QCAA sample IA2 · Question 18

Section 2 · Simple familiar (est.) · [3 marks]

Watch this question worked as an animation

A simple truss is shown.

100 kNR1R2

Calculate the reaction at supports $R_1$ and $R_2$. The length of each member is 2.5 metres. Include a force diagram to support your response.

Every member is 2.5 m, so the triangle is equilateral and the top joint is above the middle of the base. The 100 kN load is $2.5 \div 2 = 1.25$ m horizontally from each support.

The force diagram shows the outside forces only: 100 kN down on the top joint, and $R_1$ and $R_2$ up at the two bottom joints.

100 kNR₁R₂

1 mark · includes a force diagram with the 100 kN force acting vertically down on the top joint and the reactions $R_1$ and $R_2$ acting upwards at the two bottom corners

$$\begin{aligned}\Sigma M_{R_1} &= 0 \quad (\circlearrowright +) \\ 0 &= (100 \times 1.25) - (R_2 \times 2.5) \\ R_2 &= \frac{125}{2.5} = 50\ \text{kN} \uparrow\end{aligned}$$

1 mark · calculates the reaction at $R_2$

$$\begin{aligned}\Sigma F_V &= 0 \quad (\uparrow +) \\ R_1 &= 100 - 50 = 50\ \text{kN} \uparrow\end{aligned}$$

1 mark · calculates the reaction at $R_1$

The same working as a picture. Each reaction arrow is half the length of the load arrow.

The marking scheme also accepts a statement that $R_1 = 50$ kN because the truss is symmetrical and in equilibrium. When the truss and its loading are both symmetrical, each support takes half the load and you can say so.

The sample marking scheme prints the division as $125 \div 12.5$. That is a misprint for $125 \div 2.5$, and its answer of 50 kN is right.

Answer
$R_1 = 50$ kN upwards · $R_2 = 50$ kN upwards

Part 4

One joint at a time: the method of joints

If the whole truss is in equilibrium, every joint in it is in equilibrium. Cut one joint out with an imaginary pair of scissors. The forces on it are any load or reaction at that joint, plus one force from each member you cut. Those forces all pass through one point, so there are no moments to consider. That leaves two equations:

$$\Sigma F_V = 0 \qquad \Sigma F_H = 0$$

Two equations find two unknowns. So you can solve a joint only when it has no more than two unknown member forces.

  1. 1Draw the joint as a dot. Add the known forces with their real directions.
  2. 2Add each unknown member as an arrow along the member. Assume tension, so draw it pointing away from the joint.
  3. 3Resolve any sloping force into vertical and horizontal parts.
  4. 4Write $\Sigma F_V = 0$. If only one unknown has a vertical part, this equation finds it.
  5. 5Write $\Sigma F_H = 0$ to find the other.
  6. 6Read the signs. A positive answer means your assumption was right and the member is in tension. A negative answer means the member is in compression.

Assuming tension every time means the sign does the thinking for you. The sample marking scheme allows it: it accepts all members assumed in tension, or all in compression, with the force diagram corrected after the calculation.

Practise

Sample IA2 questions: one joint

QCAA sample IA2 · Question 19

Section 2 · Simple familiar (est.) · [5 marks]

Watch this question worked as an animation

A truss structure is shown.

AXYθ300 N

The truss is in static equilibrium. The reaction force $R_A$ at support A is 300 N and θ is 30°. Calculate the force in members X and Y and identify whether the members are in tension or compression. Include a force diagram to support your response.

Only three forces act on joint A: the 300 N reaction, member X and member Y. The rest of the truss does not matter. Assume X and Y are both in tension, so both arrows point away from A.

300 NXYA
First draft: both members assumed to be in tension.

1 mark · provides a force diagram with all forces shown

Y is horizontal, so X is the only unknown with a vertical part. Start with the vertical forces.

$$\begin{aligned}\Sigma F_V &= 0 \quad (\uparrow +) \\ 0 &= 300 + X\sin 30^\circ \\ X &= \frac{-300}{\sin 30^\circ} = -600\ \text{N}\end{aligned}$$

1 mark · calculates the force in member X

The negative sign means X pushes on the joint instead of pulling. X is in compression.

1 mark · determines that member X is in compression

$$\begin{aligned}\Sigma F_H &= 0 \quad (\rightarrow +) \\ 0 &= X\cos 30^\circ + Y \\ 0 &= -600\cos 30^\circ + Y \\ Y &= 519.6\ \text{N} \approx 520\ \text{N}\end{aligned}$$

1 mark · calculates the force in member Y

Y is positive, so it is in tension.

1 mark · determines that member Y is in tension

The corrected diagram. Drawn tip to tail and to scale, the three forces close into a triangle.

The marking scheme accepts Y from 519.6 N to 520 N. Does the answer make sense? The sloping top member of a roof truss is squeezed by the roof above it, and the bottom member stops the two feet from spreading apart. Top in compression and bottom in tension is the normal pattern.

Answer
X = 600 N in compression · Y = 520 N in tension

QCAA sample IA2 · Question 21

Section 2 · Complex familiar (est.) · [5 marks]

Watch this question worked as an animation

A diagram of a roller joint is shown.

HGFEθR

The roller joint has a reaction R of 35 kN. The compressive force in member GH is 12 kN and θ is 40°.

Calculate the force in member EH and identify whether the member is in tension or compression. Include a force diagram with your working.

Four forces act on joint H. Two are known: the 35 kN reaction pushing up, and GH. GH is in compression, so it pushes on the joint. GH lies to the left of H, so its push on H points to the right.

Two are unknown: FH and EH. The question only asks for EH, but EH is vertical and FH has a vertical part, so the vertical equation has both unknowns in it. Find FH first from the horizontal equation, where EH does not appear. Assume both unknowns are in tension.

35 kN12 kNFHEHH
GH is drawn pushing on the joint because it is in compression. FH and EH are assumed to be in tension.

1 mark · provides a force diagram with all forces shown

$$\begin{aligned}\Sigma F_H &= 0 \quad (\rightarrow +) \\ 0 &= 12 - FH\cos 40^\circ \\ FH &= \frac{12}{\cos 40^\circ} = 15.66\ \text{kN}\end{aligned}$$

1 mark · correctly calculates the force in member FH

FH is positive, so the assumption was right.

1 mark · determines that member FH is in tension

$$\begin{aligned}\Sigma F_V &= 0 \quad (\uparrow +) \\ 0 &= 35 + 15.66\sin 40^\circ + EH \\ EH &= -45.07\ \text{kN}\end{aligned}$$

1 mark · calculates the force in member EH

EH is negative, so it pushes down on the joint. EH is in compression.

1 mark · determines that member EH is in compression

The sample marking scheme rounds FH to 16 kN before using it, which gives EH = 45.28 kN. It accepts EH from 45 kN to 45.28 kN, and FH from 15.66 kN to 16 kN. Keeping the unrounded 15.66 kN gives 45.07 kN, which is inside the range and closer to the true value. Carry full calculator values and round at the end.

The scheme sets the question up the other way round. Its force diagram draws FH pushing into the joint, as if in compression, so its equation is $0 = 12 + FH\cos 40^\circ$ and its answer of $-15.7$ kN means tension. That is the same result by a different assumption, and the scheme accepts FH redrawn the other way once the force is known. Its vertical line does contain a slip: $0 = 35 + 16\sin 40^\circ - EH$ gives $EH = +45.28$, but the scheme prints $-45.28$. The size and the nature it states are right.

Answer
EH = 45.1 kN in compression (FH = 15.7 kN in tension)

Part 5

Working through a whole truss

To find every member, find the reactions and then move from joint to joint. The only rule is to start, and continue, at a joint with no more than two unknown members. That is usually a support.

60 kNABC4 m4 m3 m

Reactions. The truss and its load are symmetrical, so $R_A = R_B = 30$ kN.

Geometry. Member AC rises 3 m over a run of 4 m, so it is 5 m long. For its angle to the horizontal, $\sin\theta = \frac{3}{5}$ and $\cos\theta = \frac{4}{5}$. When a question gives you lengths, use the ratios straight from the triangle. You do not need the angle itself.

Joint A. Three forces: the 30 kN reaction, AC and AB. Assume both members are in tension.

$$\begin{aligned}\Sigma F_V &= 0: & 0 &= 30 + F_{AC} \times \tfrac{3}{5} & F_{AC} &= -50\ \text{kN (compression)} \\ \Sigma F_H &= 0: & 0 &= F_{AB} + F_{AC} \times \tfrac{4}{5} & F_{AB} &= 40\ \text{kN (tension)}\end{aligned}$$

Joint B. By symmetry BC also carries 50 kN in compression. If the truss were not symmetrical you would repeat the working at B.

Check at joint C. The two sloping members each push up on C with $50 \times \frac{3}{5} = 30$ kN. That is 60 kN up against the 60 kN load, so the joint balances.

The same working, one joint at a time. It ends on the finished truss. Reporting the answer on a diagram like this is a clear way to finish.

Try it yourself

Add a wind load

This truss is not symmetrical, and it has a sideways load as well as a weight. Change the two loads and watch the reactions. Then find the wind that puts member AC into tension.

Try it yourself

Change the shape of the truss

Change the load and the angle of the sloping members. The reactions depend only on the load. The member forces depend on the angle as well.

Part 6

The graphical method

The forces on a joint in equilibrium, drawn to scale one after another, tip to tail, finish exactly where they started. The shape they make is called a force polygon. With three forces it is a triangle. You can use that to find unknown forces with a ruler and a protractor and no trigonometry at all.

Here is Question 19 done by drawing.

  1. 1Choose a scale, for example 1 cm for every 100 N.
  2. 2Draw the known force to scale. The 300 N reaction is a line 3 cm long, straight up.
  3. 3From its tip, draw a faint line in the direction of one unknown member. X lies at 30° to the horizontal.
  4. 4From the starting point, draw a faint line in the direction of the other unknown member. Y is horizontal.
  5. 5The two faint lines cross at one point. That point completes the triangle.
  6. 6Measure the two new sides and convert with the scale. X measures 6.0 cm, which is 600 N. Y measures 5.2 cm, which is 520 N.
  7. 7Follow the arrows around the triangle, tip to tail, starting with the known force. Each arrow shows which way that member acts on the joint. Towards the joint means compression. Away means tension.

The animation in Question 19 above draws exactly this triangle. A scale drawing is only as accurate as your pencil, so use a large scale and a sharp point, and expect to be within a few newtons. If a question says “calculate”, use the analytical method and keep the drawing as a check.

Try it yourself

Draw the force triangle

This starts as Question 19, with a 300 N reaction and member X at 30°. Step through the drawing, then change the reaction and the angle and read the two new sides off the rulers.

Part 7

Marks and self-checks

This part pulls together what the worked examples above show about marks, then gives you the checks to run before you leave a question. The mark points are the sample marking scheme’s, sometimes reworded.

Where the sample puts the marks

Sample IA2MarksWhat each mark is for
Question 1831. Includes a force diagram with the 100 kN force acting vertically down on the top joint and the reactions $R_1$ and $R_2$ acting upwards at the two bottom corners
2. Calculates the reaction at $R_2$
3. Calculates the reaction at $R_1$
Question 1951. Provides a force diagram with all forces shown
2. Calculates the force in member X
3. Determines that member X is in compression
4. Calculates the force in member Y
5. Determines that member Y is in tension
Question 2151. Provides a force diagram with all forces shown
2. Correctly calculates the force in member FH
3. Determines that member FH is in tension
4. Calculates the force in member EH
5. Determines that member EH is in compression

One mark is one step or one idea. Where a direction, a diagram or the nature of a member has a line of its own in the table, it is a mark of its own, so write it down even when it feels obvious.

Self-checks to run inside the question

  • •Are there no more than two unknown members at the joint I chose?
  • •Is every known compression member drawn pushing on the joint?
  • •Do the forces on the joint sum to zero in both directions when I put my answers back in?
  • •Does every answer end with the word tension or compression?

Your IA2 is written by your teacher, not the QCAA. These guides are built to the syllabus and the QCAA sample exam, so the question shapes will be familiar. For practice that matches your school’s paper, your teacher is the best source.

Game plan

Your game plan for a truss joint

  1. 1Read what is given. If the reaction is given, go straight to the joint. If it is not, find the reactions first, treating the whole truss as a beam.
  2. 2Pick a joint with no more than two unknown members. Draw it as a dot with every force on it.
  3. 3Draw known forces with their real directions. A compression member pushes on the joint. Draw each unknown member pointing away from the joint.
  4. 4Find the equation with only one unknown in it and start there. A horizontal member has no part in $\Sigma F_V$. A vertical member has no part in $\Sigma F_H$.
  5. 5Use the other equation for the second unknown, keeping the sign of the first.
  6. 6Translate the signs. Positive is tension. Negative is compression.
  7. 7Write each answer as a size, a unit and the word tension or compression.

This is the short version. The full decision routine, with the question types and the wording to look for, is Game plan 2. For the shape of a written response, use Game plan 7.

Practice

Practice questions

I wrote these five to the shapes in the QCAA sample IA2 and calculated every answer in Python. Question 5 has the complex unfamiliar shape. Give yourself about 12 minutes for it.

Question 1 of 5

Skill 1: Tension and compression · Simple familiar · [1 mark]

On the force diagram of a joint, the force from a member is drawn as an arrow pointing towards the joint. The member is in

An arrow towards the joint means the member pushes on the joint. Only a member being squashed pushes back on its ends, so it is in compression. A member in tension pulls, and its arrow points away from the joint. A truss member cannot carry bending or shear, because its only forces act at its two pinned ends.

Answer
(B) compression

Question 2 of 5

Skill 2: Reactions of a truss · Simple familiar · [3 marks]

A truss is shown.

ABDE3 m3 m3 m40 kN20 kN

Calculate the reactions at supports A and B. Include a force diagram to support your response.

The force diagram needs the two loads acting down at D and E and the two reactions acting up at A and B. The members inside the truss do not appear in it.

1 mark · includes a force diagram showing both loads and both reactions

$$\begin{aligned}\Sigma M_A &= 0 \quad (\circlearrowright +) \\ 0 &= (40 \times 3) + (20 \times 6) - (R_B \times 9) \\ R_B &= \frac{240}{9} = 26.67\ \text{kN} \uparrow\end{aligned}$$

1 mark · calculates the reaction at B

$$R_A = 40 + 20 - 26.67 = 33.33\ \text{kN} \uparrow$$

1 mark · calculates the reaction at A

The heavier load is nearer A, so A carries more. Check about B: $33.33 \times 9 \approx 300$ kN m, and $40 \times 6 + 20 \times 3 = 300$ kN m.

Answer
$R_A = 33.3$ kN upwards · $R_B = 26.7$ kN upwards

Question 3 of 5

Skill 3: One joint · Simple familiar · [5 marks]

The end of a roof truss rests on a roller support, as shown.

35°PQ450 N

The truss is in static equilibrium. Calculate the force in members P and Q and identify whether each member is in tension or compression. Answer to the nearest newton. Include a force diagram to support your response.

Assume P and Q are in tension. P then pulls the joint up and to the left, and Q pulls it to the left.

450 NPQ

1 mark · provides a force diagram with all forces shown

$$\begin{aligned}\Sigma F_V &= 0 \quad (\uparrow +) \\ 0 &= 450 + P\sin 35^\circ \\ P &= \frac{-450}{\sin 35^\circ} = -784.6\ \text{N}\end{aligned}$$

1 mark · calculates the force in member P

1 mark · determines that member P is in compression

$$\begin{aligned}\Sigma F_H &= 0 \quad (\rightarrow +) \\ 0 &= -P\cos 35^\circ - Q \\ Q &= -(-784.6)\cos 35^\circ = 642.7\ \text{N}\end{aligned}$$

1 mark · calculates the force in member Q

1 mark · determines that member Q is in tension

The corrected force diagram, drawn to scale. P is the sloping force and Q is the horizontal one.

This is the mirror image of Question 19 with a different angle. The shallower the roof, the larger both forces become for the same reaction.

Answer
P = 785 N in compression · Q = 643 N in tension

Question 4 of 5

Skill 3: One joint · Complex familiar · [5 marks]

A diagram of a roller joint is shown.

KLMN55°R

The roller joint has a reaction R of 48 kN. The tensile force in member KL is 20 kN.

Calculate the force in member KN and identify whether the member is in tension or compression. Answer to one decimal place. Include a force diagram with your working.

KL is in tension, so it pulls the joint towards L, which is to the right. Assume KM and KN are in tension.

48 kN20 kNKMKNK

1 mark · provides a force diagram with all forces shown

$$\begin{aligned}\Sigma F_H &= 0 \quad (\rightarrow +) \\ 0 &= 20 + KM\cos 55^\circ \\ KM &= \frac{-20}{\cos 55^\circ} = -34.87\ \text{kN}\end{aligned}$$

1 mark · calculates the force in member KM

1 mark · determines that member KM is in compression

Keep the negative sign when KM goes into the next equation.

$$\begin{aligned}\Sigma F_V &= 0 \quad (\uparrow +) \\ 0 &= 48 + (-34.87)\sin 55^\circ + KN \\ KN &= -19.44\ \text{kN}\end{aligned}$$

1 mark · calculates the force in member KN

1 mark · determines that member KN is in compression

The corrected force diagram, drawn to scale.

KM pushes down on the joint with 28.56 kN, which takes up part of the 48 kN reaction. KN only has to push down with the remaining 19.44 kN.

Answer
KN = 19.4 kN in compression (KM = 34.9 kN in compression)

Question 5 of 5

Skills 2 and 4 · Complex unfamiliar · [8 marks]

A truss supports a sign. Wind and the weight of the sign act on joint C as shown. A is a pin support and B is a roller support.

30 kN12 kNABC2 m4 m3 m

Determine the force in each of the three members and identify whether each is in tension or compression. Answer to one decimal place.

Nothing is given except the loads, so start with the reactions. There is a horizontal load, so the pin at A has a horizontal reaction as well as a vertical one.

About A, the 30 kN load is 2 m away horizontally and the 12 kN load is 3 m away vertically. Both turn the truss clockwise.

$$\begin{aligned}\Sigma M_A &= 0 \quad (\circlearrowright +) \\ 0 &= (30 \times 2) + (12 \times 3) - (R_B \times 6) \\ R_B &= \frac{96}{6} = 16\ \text{kN} \uparrow\end{aligned}$$

1 mark · includes the moment of the horizontal load, using its vertical distance from A

1 mark · calculates the reaction at B

$$\begin{aligned}R_{AV} &= 30 - 16 = 14\ \text{kN} \uparrow \\ R_{AH} &= 12\ \text{kN} \leftarrow\end{aligned}$$

1 mark · calculates the vertical reaction at the pin, with its direction

1 mark · determines the horizontal reaction at the pin, with its direction

Joint B. Member BC runs 4 m across and 3 m up, so it is 5 m long, with $\sin\theta = \frac{3}{5}$ and $\cos\theta = \frac{4}{5}$. Assume BC and AB are in tension. BC then pulls B up and to the left, and AB pulls B to the left.

$$\begin{aligned}\Sigma F_V &= 0: & 0 &= 16 + F_{BC} \times \tfrac{3}{5} & F_{BC} &= -26.67\ \text{kN} \\ \Sigma F_H &= 0: & 0 &= -F_{AB} - F_{BC} \times \tfrac{4}{5} & F_{AB} &= 21.33\ \text{kN}\end{aligned}$$

1 mark · calculates the force in BC and identifies compression

1 mark · calculates the force in AB and identifies tension

Joint B with the signs read, drawn to scale. BC is the sloping force and AB is the horizontal one.

Joint A. Member AC runs 2 m across and 3 m up, so its length is $\sqrt{13}$ m and it makes $\tan^{-1}\left(\frac{3}{2}\right) = 56.3^\circ$ with the horizontal. Assume AC is in tension.

$$\begin{aligned}\Sigma F_V &= 0 \quad (\uparrow +) \\ 0 &= 14 + F_{AC}\sin 56.3^\circ \\ F_{AC} &= -16.83\ \text{kN}\end{aligned}$$

1 mark · determines the angle or ratios for member AC

1 mark · calculates the force in AC and identifies compression

Check. The horizontal forces at A have not been used yet. To the left: the 12 kN reaction and the horizontal push of AC, $16.83\cos 56.3^\circ = 9.33$ kN, a total of 21.33 kN. To the right: AB pulling with 21.33 kN. They agree, so all three members are right.

Joint A, drawn to scale. The polygon closing is the check.
Answer
AB = 21.3 kN in tension · BC = 26.7 kN in compression · AC = 16.8 kN in compression

Sources: Engineering 2025 v1.4 general senior syllabus, Unit 3 Topic 2 and the IA2 specifications. QCAA Engineering 2025 v1.4 IA2 sample assessment instrument and sample marking scheme. Engineering formula and data book 2025 v1.4. Every numerical answer was calculated in Python.

Questions marked “QCAA sample IA2” are quoted from the Engineering 2025 v1.4 IA2 sample assessment instrument, and their mark points are drawn from its sample marking scheme, sometimes reworded, © State of Queensland (QCAA) 2026, licensed under CC BY 4.0. Their figures are redrawn. All other questions are Tangent Tuition’s own. Tangent Tuition is not affiliated with the QCAA.