Game plan 2 · Unit 3 Topic 2

Trusses

Reactions, the method of joints, the method of sections and the graphical method. Together they are the largest calculation topic in the sample.

Reach for it when

There is a truss on the page. The question wants the support reactions, the force in one or two members, or whether a member is in tension or compression.

The QCAA sample IA2 has four truss questions worth 19 marks: Question 18 (reactions, 3 marks), Questions 19 and 21 (one joint each, 5 marks each) and Question 25 (the method of sections, 6 marks). All four say to include a force diagram. Your teacher writes your IA2, so the marks and question numbers here describe the QCAA sample, not your paper.

Part 1

The split this game plan is built on

Read what the question gives you and which member it wants. That decides the method, and the wrong method can turn a five-minute question into a twenty-minute one.

Ask this first

What is given, and where is the member?

Reactions wanted

“Calculate the reaction at supports $R_1$ and $R_2$.”

→ Game plan 2.1. Treat the whole truss as one beam.

A member at a joint with a known force

A reaction or a member force is given at the joint, and no more than two members there are unknown.

→ Game plan 2.2. One joint, two equations.

A member in the middle of the truss

Nothing is known at either end of the member, and reaching it joint by joint would take several joints.

→ Game plan 2.3. Cut the truss.

If the question says “graphical method” or gives you grid paper and a scale, use Game plan 2.4. If it says “calculate”, use the equations.

Habit

Count the unknown members at the joint before you start. More than two means you are at the wrong joint, or you need the method of sections.

Part 2

The four game plans

Every truss member is either pulled or pushed along its own length, and nothing else. That one fact is why a joint only needs two equations.

Game plan 2.1

Reactions of a truss

The supports are the unknowns.

  1. 1Draw the outside forces only: the loads and the reactions. Leave the members out.
  2. 2Find the horizontal distance from one support to each load, using the truss dimensions.
  3. 3Take moments about one support and solve for the other reaction, exactly as in Game plan 1.1.
  4. 4Sum the vertical forces for the remaining reaction.
  5. 5If the truss and its loading are both symmetrical, each support takes half the load and you can say so. The sample marking scheme accepts that statement in Question 18.
  6. 6State each reaction with its size, unit and direction.
Game plan 2.2

One joint: the method of joints

A known force at the joint, and one or two unknown members.

  1. 1Draw the joint as a dot with every force that acts on it. This is the force diagram the question asks for.
  2. 2Draw known forces in their real directions. A reaction pushes up. A member in compression pushes on the joint, and a member in tension pulls on it.
  3. 3Draw each unknown member pulling away from the joint, as if in tension.
  4. 4Resolve any sloping member into a horizontal part and a vertical part.
  5. 5Start with the equation that has one unknown in it. A horizontal member has no part in $\Sigma F_V$, and a vertical member has no part in $\Sigma F_H$.
  6. 6Use the other equation for the second unknown, keeping the sign of the first.
  7. 7Read the signs. Positive means your assumption was right and the member is in tension. Negative means compression.
  8. 8Write each answer as a size, a unit and the word tension or compression. The nature is a separate mark from the size.
Game plan 2.3

One member: the method of sections

The member is in the middle of the truss.

  1. 1Label the truss with joint letters or Bow’s notation. The sample marking scheme gives a mark for a labelling notation and a valid cut.
  2. 2Find the reactions of the whole truss with Game plan 2.1.
  3. 3Cut through the member you want and no more than two others. Keep the piece with fewer forces on it.
  4. 4Draw that piece alone with its loads and reactions, and each cut member as an arrow pulling away from it.
  5. 5Find the angle of any sloping cut member from the truss dimensions.
  6. 6Choose the equation that has only your member in it, using the box below.
  7. 7Read the sign and state the size, the unit and tension or compression.

Choosing the equation

  • •If the two unwanted members meet at a joint, take moments about that joint. Both pass through it and drop out.
  • •If the two unwanted members are horizontal, sum the vertical forces. Neither has a vertical part.
  • •If neither works at once, find one unwanted member first and then use it. The sample marking scheme does this in Question 25 with two moment equations.
Game plan 2.4

The graphical method

The question asks for a scale drawing.

  1. 1Choose a scale and write it down, for example 1 cm for every 100 N. A larger drawing is a more accurate one.
  2. 2Draw the known force to scale in its real direction.
  3. 3From its tip, draw a faint line in the direction of one unknown member.
  4. 4From its starting point, draw a faint line in the direction of the other unknown member.
  5. 5Where the two faint lines cross, the force polygon closes.
  6. 6Measure the two new sides and convert them with the scale.
  7. 7Follow the arrows around the polygon tip to tail, starting with the known force. An arrow towards the joint means compression. An arrow away from it means tension.

Part 3

Two worked chains and the traps around them

Both are from the QCAA sample IA2. The first is Game plan 2.2 and the second is Game plan 2.3.

Sample IA2 Question 19 · One joint · 5 marks

At support A the reaction is 300 N upwards. Member X slopes at 30° and member Y is horizontal. Assume both pull on the joint.

Vertical forces. Y has no vertical part, so start here: $0 = 300 + X\sin 30^\circ$, so $X = -600$ N. Negative, so X pushes on the joint: 600 N in compression.

Horizontal forces. $0 = Y + X\cos 30^\circ = Y - 519.6$, so $Y = 519.6$ N. Positive, so Y is in tension.

The corrected diagram. Drawn tip to tail and to scale, the three forces close into a triangle.

Sample IA2 Question 25 · One member in the middle · 6 marks

Reaction. Moments about the right support: $0 = -(90 \times 3.5) - (50 \times 5.25) + (R_L \times 10.5)$, so $R_L = 55$ kN upwards.

Cut and angle. Cut the top member, Z and the bottom member, and keep the left piece. Z rises 3.0 m over 1.75 m, so $\theta = \tan^{-1}(3 \div 1.75) = 59.7^\circ$.

The scheme’s route. Moments about joint 2 give the top member: $0 = (55 \times 3.5) + (F_{AF} \times 3)$, so $F_{AF} = -64.2$ kN. Moments about joint 1 then give Z: $0 = (F_{AF} \times 3) - (Z\sin 59.7^\circ \times 3.5)$, so $Z = -63.7$ kN.

The shorter route. The two unwanted members are horizontal, so sum the vertical forces on the piece: $0 = 55 + Z\sin 59.7^\circ$, so $Z = -63.7$ kN. Either way Z is 63.7 kN in compression.

The cut for Question 25. The forces shown on the cut members are the answers worked out in Part 5.

The traps that cost whole questions

  • •A known compression member drawn pulling. In Question 21 the 12 kN in GH pushes on joint H. Drawn the other way, every answer after it is wrong.
  • •The equation with two unknowns. In Question 21 the vertical equation holds both FH and EH. Find FH from the horizontal equation first.
  • •The sign left unread. $-600$ N is not the answer. 600 N in compression is.
  • •The angle guessed. In Question 25 the angle of Z comes from 3.0 m over half a panel, 1.75 m, not over the whole 3.5 m.

Part 4

Tension, compression and the sign of your answer

TensionCompression
What the member feelsIt is being stretchedIt is being squashed
What it does to the jointPulls on it. The arrow points away from the jointPushes on it. The arrow points towards the joint
Your answer, if you assumed tensionPositiveNegative
Colour in the Topic GuidesBlueOrange

A given compression force goes into your equation the way it really acts. In Question 21 the 12 kN compression in GH pushes on joint H, so its arrow points into the joint from the side GH is on.

You can assume compression for an unknown member if you prefer, and then a negative answer means tension. The sample marking scheme does this for one member of Question 21. Either assumption earns the marks as long as your diagram, your equation and your conclusion agree with each other.

Habit

Finish every member with the word. “600 N” is half an answer. “600 N in compression” is the whole answer.

A member in tension pulls on the joints at its ends. A member in compression pushes on them. In these guides tension is blue and compression is orange.

Part 5

When the question wants every member

  1. 1Find the reactions.
  2. 2Start at a support joint, where only two members meet.
  3. 3Move to a neighbouring joint that now has no more than two unknowns, and carry each solved member across.
  4. 4A member in tension pulls on the joints at both of its ends. A member in compression pushes on both.
  5. 5Use the last joint as a check. Its forces should already balance.

Look for the short cuts before you start. At a joint where only two members meet in different directions and no load or reaction acts, both carry no force. In a symmetrical truss with symmetrical loading, matching members carry matching forces.

Part 6

What the formula book gives you

It gives the components $F_H = F\cos\theta$ and $F_V = F\sin\theta$, the resultant $F_T = \sqrt{F_H^2 + F_V^2}$, $\tan\theta = \frac{F_V}{F_H}$ and $M = Fd$. It does not print the equilibrium equations, either method, Bow’s notation or the meaning of a negative answer.

Part 7

Common QCAA language for trusses

The question saysYour move
“Calculate the reaction at supports $R_1$ and $R_2$”Game plan 2.1. Outside forces only.
“The length of each member is 2.5 metres”Every triangle is equilateral, so a top joint sits above the middle of the member below it.
“The truss is in static equilibrium”The forces on every joint sum to zero in both directions.
“The reaction force $R_A$ at support A is 300 N”The reaction is given, so go straight to that joint with Game plan 2.2.
“The compressive force in member GH is 12 kN”A known member. Draw it pushing on the joint.
“Calculate the force in members X and Y and identify whether the members are in tension or compression”Four things to state: two sizes and two natures.
“Calculate the force in member Z”One member in the middle of the truss. Game plan 2.3.
“Include a force diagram to support your response”A joint diagram for Game plan 2.2, or the cut piece for Game plan 2.3. It is marked.

Wording quoted from the QCAA Engineering 2025 v1.4 IA2 sample assessment instrument and its sample marking scheme is © State of Queensland (QCAA) 2026, licensed under CC BY 4.0. Tangent Tuition is not affiliated with the QCAA.