Engineering · Unit 3 · QCAA sample IA2 All sample IA2 questions
QCAA sample IA2 · Section 2 · Calculation

Question 22

[4 marks] Complex familiar (est.)

Your teacher writes your IA2. This is the QCAA sample, so use it for the question shapes, and ask your teacher for practice that matches your school’s paper.

The question [4 marks]

A simply supported beam is shown.

O1000 N600 N1000 N45°9 mx7 mNote: not drawn to scale
Redrawn from the QCAA sample.

The beam is balanced at point O.

Calculate the total length of the beam. Assume that the beam is without mass.

Watch the solution first

Balance the moments about O, then add up the lengths

The beam is a seesaw on O. Watch which way each force turns it, why only part of the angled force counts, and how every lever arm is measured from O.

O9 mx7 mNot to scale1000 N600 N45°45°1000 Nanticlockwiseclockwise707.1 N707.1 Nthrough Oall 1000 N?Full 1000 N used: 1600x = 2000, x = 1.25 m9 mxx + 73.1 m9 + 3.1 + 7 = 19.1 mΣMO = 0, clockwise +1000 sin 45° = 707.1 N0 = −(1000 × 9)+ 600x+ 707.1(x + 7)x = 3.1 m9 + 3.1 + 7 = 19.1 mMark 1Mark 2Mark 3Mark 4Call the unknown distance x. The total length is 9 + x + 7.The beam is balanced, so the moments about O sum to zero.Only the perpendicular part turns the beam: 1000 sin 45° = 707.1 N.Using the full 1000 N gives x = 1.25 m. Only 707.1 N turns the beam.0 = −(1000 × 9) + 600x + 707.1(x + 7), clockwise positive.1307.1x = 4050.3, so x = 3.1 m.Total length = 9 + 3.1 + 7 = 19.1 m.

The dashed arrows are the two parts of the angled force. They replace it in the working. They are not extra forces.

Now for the engineering

Slide the 600 N force until the seesaw balances

The beam is drawn to scale here, and it tips towards the bigger moment total. Slide $x$ to move the 600 N force, and the angled force 7 m beyond it, along the beam. Change the angle of the 1000 N force to see how much of it turns the beam. Then try each slip to see where it leaves the real beam.

O 1000 N 600 N 1000 N 9 m 7 m
solid: a force dashed: the part perpendicular to the beam dotted: the part along the beam
Anticlockwise about O (solid) 9000 N m Clockwise about O (hatched)
Try a common slip

QCAA sample marking scheme · 4 marks

Work through the solution one mark at a time

Try each step yourself before you reveal it. The mark numbers match the chips in the film and the slips in the seesaw above.

Step 1 · Moments about OMark 1

Call the unknown distance from O to the 600 N force $x$. The total length is then $9+x+7$, so the job is to find $x$.

The beam is balanced, so the moments about O sum to zero. The left-hand 1000 N force turns the beam anticlockwise. The 600 N force and the vertical part of the angled force turn it clockwise.

$$\Sigma M_O=0\quad(\circlearrowright+)$$

Why?

A balanced beam is in equilibrium. Taking moments about O also removes the reaction at the pivot, because that force has no lever arm about O.

The question calls this a simply supported beam, but it is a beam on one pivot. The sentence that matters is “the beam is balanced at point O”.

Marker: recognises that the beam is in equilibrium and therefore the length of x can be determined through the sum of the moments about O

Step 2 · The part of the angled force that turns the beamMark 2

Only the part of the angled force that is perpendicular to the beam has a moment about O. The part along the beam points straight through O.

$$\begin{aligned}F_V&=F\sin\theta\\&=1000\sin45^\circ\\&=707.1\text{ N}\end{aligned}$$

Why?

A moment is a force times its perpendicular distance from the pivot. The horizontal part of the angled force, also 707.1 N, has a line of action through O. It is resisted by the pivot and plays no part in the balance.

Marker: recognises that the vertical component of the 1000 N force acting at 45° to the beam must be determined using trigonometry

Step 3 · The moment equationMark 3

The 600 N force is $x$ from O. The angled force is $x+7$ from O.

$$\begin{aligned}\Sigma M_O&=0\quad(\circlearrowright+)\\0&=-(1000\times9)+600x+707.1(x+7)\\0&=-9000+600x+707.1x+4949.7\\1307.1x&=4050.3\\x&=3.1\text{ m}\end{aligned}$$

Why?

Every lever arm is measured from O, not from the next force along. The left-hand force turns the beam anticlockwise, so its moment is negative when clockwise is positive.

Marking

Allow FT marks

Marker: calculates the length of x

Step 4 · The total lengthMark 4

Add the three lengths along the beam.

$$\begin{aligned}\text{total length}&=9+3.1+7\\&=19.1\text{ m}\end{aligned}$$

The beam is $19.1\text{ m}$ long.

The scheme writes its answer as 19.1 m ≈ 19 m.

Marker: calculates the total length of the beam

Common errors

If I had to guess where you might lose marks…

  • Using the full 1000 N. You write $0=-9000+600x+1000(x+7)$, so $1600x=2000$, $x=1.25\text{ m}$ and a total of $17.25\text{ m}$. You lose Mark 2. The force is at $45^\circ$ to the beam, so only $1000\sin45^\circ=707.1\text{ N}$ of it turns the beam.
  • Taking the lever arm of the angled force as 7 m. You write $0=-9000+600x+707.1\times7$, so $600x=4050.3$, $x=6.75\text{ m}$ and a total of $22.75\text{ m}$. You lose Mark 3. The 7 m is measured from the 600 N force. From O the lever arm is $x+7$.
  • Stopping at $x$. You balance the beam, write $x=3.1\text{ m}$ and move on. You lose Mark 4. The question asks for the total length of the beam, $9+3.1+7=19.1\text{ m}$.

Only mark this done when you could do it without help. Reading the solution does not count.

Back to the index

Question wording is from the QCAA Engineering 2025 v1.4 IA2 sample assessment instrument, and the marker lines are from its sample marking scheme, © State of Queensland (QCAA) 2026, licensed under CC BY 4.0. Figures are redrawn. The solutions, animations and commentary are Tangent Tuition’s. Tangent Tuition is not affiliated with the QCAA.