Engineering · Unit 3 · QCAA sample IA2 All sample IA2 questions
QCAA sample IA2 · Section 2 · Written response

Question 16

[5 marks] Simple familiar (est.)

Your teacher writes your IA2. This is the QCAA sample, so use it for the question shapes, and ask your teacher for practice that matches your school’s paper.

The question [5 marks]

The diagram shows how a concrete beam is prestressed.

Tension the prestressing tendons against the end abutmentsTendonPrecasting bedCast the beam concreteConcreteRelease the end anchorages, prestressing the beam
Redrawn from the QCAA sample.

Explain how and why concrete beams are prestressed with reference to the diagram.

Watch the solution first

Follow the three stages of the diagram, then ask what a load does

Not to scale. The film walks through the diagram one stage at a time, using its labels, then puts a load on the finished beam. Watch which way each pair of arrows points.

Stage 1 · Tension the prestressing tendons against the end abutmentsStage 2 · Cast the beam concreteStage 3 · Release the end anchorages, prestressing the beamEnd abutmentEnd abutmentPrecasting bedConcrete, wetConcrete, curedTendonit stretchesreleasedreleasedTension in the tendons: the arrows pull apartCompression in the concrete: the arrows push togetherPrestressed beamLoadAt the bottom fibrebuilt-in compressiontension from the loadNo cracksPlain concrete beamLoadAt the bottom fibreno built-in compressiontension from the loadCracksHow: stretch the tendons, cast and cure, release, and the tendons squeeze the concreteWhy: to resist tension under load, because concrete is weak in tensionMark 1Mark 2Mark 3Mark 4Mark 5A precasting bed with two end abutments, and steel tendons run between themThe tendons are stretched against the end abutments before any concrete is pouredThe beam concrete is cast around the stretched tendons and left to cureOnce the concrete has cured, the end anchorages are releasedThe bonded tendons try to shorten, which squeezes the concrete into compressionUnder load, tension at the bottom must first overcome the built-in compressionConcrete is weak in tension but strong in compression, so a plain beam cracksThree marks for how it is done, two marks for why
Now for the engineering

Order the stages, sort the how from the why, then load the beam

Tap the three stages in the order they happen, then send each statement card to How, Why or Leave out. The checklist shows which marks your response earns. Then use the load slider to compare a plain concrete beam with a prestressed one.

Step 1 · Put the stages in order
1stPick a stage2ndPick a stage3rdPick a stage
Slack tendon Tendon in tension Compression in the concrete

Step 2 · Sort each statement into how or why
Marks earned
Try a common slip

Step 3 · Load a plain beam and a prestressed beam
Plain concrete beamPrestressed beam
Tension: dashed, pulling apart Compression: solid, pushing together Tendon

A simple model, not a real design. Each 1 kN of load adds 0.5 MPa of tension at the bottom fibre. The prestress builds in 8.0 MPa of compression there. The concrete cracks once the tension passes 3.0 MPa.

QCAA sample marking scheme · 5 marks

Work through the solution one mark at a time

Try to write each sentence yourself before you reveal it. Three marks are for how the beam is prestressed and two are for why.

Mark 1Stage 1 of the diagram

How. As the first stage of the diagram shows, steel tendons are fixed at one end of the precasting bed and stretched against the end abutments, within their elastic limit, before any concrete is poured.

Why?

The order is the point. In the diagram the tendons are stretched while the bed is still empty, so say “before any concrete is poured” in so many words.

Marker: describes how concrete beams are prestressed using wording that indicates tension is applied to the steel cables/tendons before the concrete is poured

Mark 2Stages 2 and 3 of the diagram

The beam concrete is then cast around the tendons, as in the second stage. Once the concrete has cured, the end anchorages are released, as in the third stage.

Why?

The release only works once the concrete has cured and gripped the tendons. Say “cured” before you say “released”.

Marker: describes how concrete beams are prestressed using wording that indicates tension is released on the steel cables/tendons after the concrete is cured

Mark 3What the release does

The tendons try to return to their original length. Because they are bonded to the concrete, they shorten and squeeze it, which introduces compressive forces into the beam.

Why?

This sentence names the result of the process. The stretched steel pulls inwards on the concrete it is bonded to, so the concrete ends up in compression.

Marking

Accept other suitable response consistent with a reasonable understanding.

Marker: describes how concrete beams are prestressed using wording that indicates the shortened steel cables/tendons increase the compressive forces in the beam

Mark 4The purpose

Why. Concrete beams are prestressed to improve their capacity to resist the tensile forces that occur when they are under load.

Why?

The purpose has to name the tensile forces and the load. A beam that bends under load is stretched along its bottom edge.

Marker: explains why the concrete beams are prestressed including to improve on their capacity to resist the tensile forces applied when under load

Mark 5The reason

This is needed because concrete is very weak in tension but strong in compression. The built-in compression must be overcome before any part of the beam goes into tension.

Why?

This is a property of the material, and it is a separate mark from the purpose. Give it a sentence of its own.

How: tension the tendons, cast and cure the concrete, release, and the tendons squeeze the beam. Why: to resist tension under load, because concrete is weak in tension.
Marking

Accept other suitable response consistent with a reasonable understanding.

Marker: explains why the concrete beams are prestressed including recognition that concrete is weak in tension but strong in compression

The model response in full

How. As the first stage of the diagram shows, steel tendons are fixed at one end of the precasting bed and stretched against the end abutments, within their elastic limit, before any concrete is poured. Mark 1 The beam concrete is then cast around the tendons, as in the second stage. Once the concrete has cured, the end anchorages are released, as in the third stage. Mark 2 The tendons try to return to their original length. Because they are bonded to the concrete, they shorten and squeeze it, which introduces compressive forces into the beam. Mark 3

Why. Concrete beams are prestressed to improve their capacity to resist the tensile forces that occur when they are under load. Mark 4 This is needed because concrete is very weak in tension but strong in compression. The built-in compression must be overcome before any part of the beam goes into tension. Mark 5

The response follows the three captions of the diagram in order and borrows their words: tendons, end abutments, cast, release. Then it gives the purpose and the reason as two separate sentences, one for each “why” mark.

Common errors

If I had to guess where you might lose marks…

  • Tensioning after the pour. If you write that the concrete is cast and the tendons are tensioned afterwards, you have described post-tensioning. The diagram shows the tendons stretched against the end abutments while the bed is still empty. You lose Mark 1.
  • Stopping at “to make it stronger”. Stronger against what? You need to name the tensile forces that occur under load, and then say that concrete is weak in tension but strong in compression. Without those two ideas you lose Marks 4 and 5.
  • Giving only the how. Three accurate sentences about the stages earn three marks and no more. The question says “how and why”, so finish with the purpose and the reason. Leaving them out costs you Marks 4 and 5.
  • Tension and compression reversed. If you write that the released tendons put the concrete into tension, you have it backwards. The stretched tendons try to shorten and squeeze the concrete, so the concrete goes into compression. You lose Mark 3.

Only mark this done when you could do it without help. Reading the solution does not count.

Back to the index

Question wording is from the QCAA Engineering 2025 v1.4 IA2 sample assessment instrument, and the marker lines are from its sample marking scheme, © State of Queensland (QCAA) 2026, licensed under CC BY 4.0. Figures are redrawn. The solutions, animations and commentary are Tangent Tuition’s. Tangent Tuition is not affiliated with the QCAA.