Engineering · Unit 3 · QCAA sample IA2 All sample IA2 questions
QCAA sample IA2 · Section 1 · Sentence response

Question 12

[2 marks] Simple familiar (est.)

Your teacher writes your IA2. This is the QCAA sample, so use it for the question shapes, and ask your teacher for practice that matches your school’s paper.

The question [2 marks]

Dry corrosion of metals is evident when …………………………………………………………

Watch the solution first

Watch what reacts, then check what is missing

Not to scale. A bare metal surface sits in air. Watch what arrives at the surface and what forms there, then notice what the picture never contains.

metaldry airO2oxide layerno waterno electrolyteDry corrosion of metals is evident when …oxidation occurswithout the presence of moistureMark 1Mark 2wet corrosion, for contrastelectrolyte (water)anodecathodee−A bare metal surface sits in dry air.Oxygen from the air reaches the metal surface.The metal reacts directly with the oxygen. That is oxidation.No moisture took part. There is no electrolyte.Wet corrosion needs an electrolyte, an anode and a cathode. Not here.Two ideas, two marks: oxidation, and no moisture.
Now for the engineering

Set the conditions, then finish the sentence

Switch moisture, oxygen and heat on and off, and read which type of corrosion the conditions describe. Then pick an ending for the sentence and see which of the two marks it earns. Each ending also sets the picture to the conditions it describes.

metalO2no oxygen reaches the surfacemoisture (electrolyte)anodecathodee−thin oxide layerthick oxide layerhot metalnormal temperature
Oxygen, hollow circlesMoisture, dashed outlineOxide layer, dotted fillMetal, hatched

Finish the sentence

Dry corrosion of metals is evident when …

Your sentence

Your sentence appears here when you pick an ending.

Marks earned
Used… ✗
Correct… oxidation occurs without the presence of moisture✓

QCAA sample marking scheme · 2 marks

Work through the solution one mark at a time

Try to finish the sentence yourself before you reveal each step. The two marks are for two separate ideas.

Mark 1The first idea: what the process is

In dry corrosion the metal reacts directly with oxygen, or another gas, and an oxide layer forms on its surface. The name for that reaction is oxidation, so the ending starts with it.

Dry corrosion of metals is evident when oxidation occurs …

Why?

The first mark is for naming what causes the corrosion. There is no cell here, only the metal and the gas, so the cause is oxidation.

Marking

Accept chemical attack

Marker: identifies that corrosion is caused by oxidation

Mark 2The second idea: what is missing

What makes the corrosion dry is that no moisture takes part. With no water on the surface there is no electrolyte, so the ending finishes by saying so.

… without the presence of moisture.

Why?

Wet corrosion also starts with oxidation. What separates the two types is whether moisture is there to act as an electrolyte, so the second mark is for saying that it is absent. I read the note below as allowing the word water in place of moisture, which matches the marker line.

Marking

Accept presence of water

Marker: identifies that the oxidation occurs when there is no moisture/water present

Step 3The completed sentence

Put the two ideas together in one ending.

Dry corrosion of metals is evident when oxidation occurs without the presence of moisture.
Why?

Two marks, two ideas: what the process is, and what is missing. An ending with only one of them earns only one mark.

The model response in full

Dry corrosion of metals is evident when oxidation occurs Mark 1 without the presence of moisture. Mark 2

Common errors

If I had to guess where you might lose marks…

  • Only the condition. You write “the metal is not wet”. That is the second idea, so it earns Mark 2, but you never say what the process is. You lose Mark 1. Name it: oxidation.
  • Only the process. You write “the metal oxidises”. That earns Mark 1, but oxidation is also the first step of wet corrosion, so your sentence does not separate dry from wet. You lose Mark 2. Add that no moisture is present.
  • Describing wet corrosion. You write about moisture acting as an electrolyte between an anode and a cathode. That is an electrochemical cell, which is wet corrosion. You lose Mark 1 and Mark 2.
  • Giving the temperature. You write “the metal is hot”. Heat makes dry corrosion much faster, but it is not what makes it dry, and a hot metal with moisture on it still corrodes wet. You lose Mark 1 and Mark 2.

Only mark this done when you could do it without help. Reading the solution does not count.

Back to the index

Question wording is from the QCAA Engineering 2025 v1.4 IA2 sample assessment instrument, and the marker lines are from its sample marking scheme, © State of Queensland (QCAA) 2026, licensed under CC BY 4.0. Figures are redrawn. The solutions, animations and commentary are Tangent Tuition’s. Tangent Tuition is not affiliated with the QCAA.